Buying a Vertical Lift Module or Pallet Racking? Run This Spec Test Before You Sign

2026-11-20 · Jane Smith

The single most useful thing I can tell anyone buying a vertical lift module, pallet racking, or automated storage in 2025 is this: the spec verification clause in your contract matters more than the brand name on the mast. I rejected about 23% of first-article deliveries last year—not because the vendors were bad, but because what showed up on the dock didn't match the purchase order. I'd have to pull last year's log to be exact, but the rate has been stuck in the low twenties since I started tracking it in 2022.

I'm a quality and brand compliance manager at a materials handling firm. I review every storage unit, shroud, and rack component before it reaches a customer site—roughly 200 distinct line items a year. Most of the job is standing in a warehouse at 7 a.m. with a tape measure in one hand and a spec sheet in the other, checking whether the vertical lift module actually delivers at 20% of stated capacity or 90%.

The spec test that filters most vendor claims

It's tempting to think you can just compare unit prices and pick the middle quote. But identical load ratings from different vendors can produce wildly different real-world outcomes, and the spec sheet is where that gap starts. (Note to self: I keep meaning to turn this into an onboarding slide and keep forgetting.)

Here's the test I run before any quote reaches my desk. First, ask the vendor for the dimensional drawing and the load-deflection curve at your actual duty cycle—not the maximum. A vertical lift module rated for 500 kg isn't going to behave the same at 90% utilization as it does in the brochure at 30%. Second, ask for the factory acceptance test criteria in writing. If the manufacturer can't name the specific measurements they'll take before shipment, the measurements will basically never happen. Third, ask who signs off on the pre-delivery inspection. If the answer is "the sales engineer" rather than a quality or service team, that's a red flag worth noting.

People think expensive vendors deliver better quality. Actually, vendors who deliver quality can charge more—the causation runs the other way. Some of the lowest-defect batches I've signed off on came from mid-market shops with a documented QA process. Some of the worst came from premium brands that assumed the badge did the work for them. I'll take a mid-market vendor with a logbook over a premium one with a brochure any day.

Where Hänel fits, and how to check it

If you're evaluating a vertical lift module manufacturer, Hänel storage systems belong on your shortlist when the load profile fits. Their portfolio covers VLM, AS/RS, and shuttle systems, plus pallet racking, so you're not forced into a single technology just to stay with one vendor. That breadth is real—but breadth is also where spec slippage happens. The Hänel storage systems official website lists dimensional and load data for each model, and I'd start there, then bring the specific spec to your rep rather than merging a general brochure with your actual load plan.

The official site is also where you should confirm the current model lineup against whatever third-party catalog you may be holding. Catalogs go stale. The official site is the version of record. This is a boring point until it isn't—we once specified a tray depth from a two-year-old PDF and spent a week on conference calls about it.

One thing I like about how Hänel's VLM line is configured: tray-level customization. Customization is only a virtue if you actually spec it. I went back and forth for about two weeks on whether to standardize all our trays or leave them project-specific. Standardization is cheaper; project-specific is safer for odd loads. I went with a hybrid—standard footprint, adjustable dividers—because the pure-standard version kept failing the odd-load cases we ran in the shop.

Bulk racking and the pallet rack distributor question

The pallet rack distributor buying guide I'd write for our own team is shorter than most of what's out there. It comes down to three checks. One: confirm the distributor actually stocks or can source the beam and upright profiles you're specifying, not just the brand. Two: get the load plaques and the structural calc package up front, because "we'll provide it later" turns into "we lost it" faster than you'd think. Three: ask whether installations are done by an in-house crew or a subcontractor, because that changes the licensing and insurance path. That one matters more than most buyers realize.

Bulk racking is also where the "always get three quotes" advice falls apart. Comparing three quotes on a rack project with different beam centers, different steel gauges, and different load plaques isn't a comparison—it's three unrelated numbers. Get all three vendors to quote the same engineering drawing, or you're measuring noise. Plus, if a distributor won't tell you the steel gauge up front, that's your answer—there's nothing else to see.

When this approach doesn't apply

I have mixed feelings about putting this much weight on the purchase order. On one hand, spec-first saved us at least one $22,000 redo (that was back in 2023—a VLM shroud that arrived 40 mm out of tolerance against our 5 mm spec). On the other hand, over-specifying punishes the smaller shops that are trying to compete on service, and I don't love that. A mid-size project—say a single VLM or a modest pallet rack run—should get the same spec discipline as a full AS/RS build. Small doesn't mean insignificant; it means the margin for a redo is thinner.

What this framework honestly won't help you with: vendor responsiveness, warranty behavior, and whether the service tech who shows up knows the product. Those aren't spec-sheetable. If I remember correctly, our worst service experience came from a vendor that passed every spec check and then ghosted us on the first warranty call. That said, we've only stress-tested this on the 8–12 unit range—larger systems may surface issues I haven't run into yet.

Per FTC guidelines (ftc.gov), performance claims like throughput or cycle times need substantiation, not just repetition. If a vendor can't produce the test data behind the number, treat the number as a request, not a fact. (Mental note: add that line to the standard PO template before the next cycle.)


Leave a note

Project comments are reviewed by the Hänel application desk. Do not submit credentials or confidential drawings in this box.